Technical features:
New design - Reduced dimensions to allow installation in short bays - Maximum programming flexibility - Brushes electronic power control - Overlapping system with side brushes that are automatically blocked in the forward gantry run to improve washing of the lower parts and free to tilt in the backward run to follow the vehicle's profile - Inverter device controlling the top brush and the top blower raising movement - Drying system with 4 low noise air blowers - Contour following top dryer - Side dryer equipped with the exclusive TSD system which enhances the side drying efficiency through a contour following device - High pressure system, up to 80 bar, with two side arches and one contour following top arch - LED traffic lights with new signals to position the vehicle - Low power consumption - Supervision and diagnostic via SMS - “Fault tolerant” control system (faulty components are automatically excluded if minor alarms occur reducing therefore down times) - Hot dip galvanized gantry
Overall dimensions:
Structure width: 3460 mm
Structure length: 1600 mm
Gantry height: 3150 mm
Washing width: 2400 mm
Washing height: 2400 mm
Maximum power consumption: 17,2 kW
(water pumps not included)
Main accessories:
In-built wheel wash device / In-built Robowash system / Underchassis wash / Short track device / High and medium pressure systems / Pre-wash side and top arches with distribution of hot chemicals / Maximum flexibility to fit further chemical products dosing pumps (shampoo and wax) / Polish product and cycles / Wheel rims cleaner and cycles / Possibility to use osmotic water / Maximum flexibility to cope with special vehicles shapes (ex. pick-up programme) / “Foam touch” brushes / Centralized lubrication system / Different payment and activation systems.
Hydrus boasts Ceccato technology that surpasses other high-end systems, making flexibility and reliability its strong points.
It is the ideal solution for those seeking the bare basics or those who intend to offer a complete service.
Main features
- Traffic light system to guide the car wash user during the positioning of his vehicle, a system with three high luminosity LED lamps is fitted on the front cladding of the washing unit
- The brushes are electronically controlled. Thank to an inverter device, the top brush and the top dryer movements are very soft and they can therefore follow the profile of the vehicle in a very smooth, precise and accurate way
- When in operation, the side brushes carry out a sequence of movements called overlapping. The washing action will be repeated several times on the front and rear parts of the vehicle (generally the dirtiest ones) in order to reach and perfectly clean also the centre line, eliminating the shadow zone that remains when washing with traditional systems
- Hot dip galvanised and painted gantry frame
- Double hydraulic circuit, for fresh and recycled water
Hot Hi Foam Car Wash
Technical Features:
Stainless Steel Cabinet with polystyrene insulation
Cat 340 Pump @ 13 litres / minute (1300 p.s.i.)
2.2 KW Motor @ 220 Volts
or
3 KW Motor @ 350 Volts
State of the art Electrical Microprocessor
TEHA Boiler @ 65KW / Diesel
or
TEHA Boiler @ 25KW / Electrical.
500 watt heater thermostatically controlled via a thermostat for Frost Protection.
Industrial Water Softener with Brine Tank.
Colour to Customer's Specification.
Automatic Programme to customers specification
Manual - Key Operation.
12 Months Part & Labour Warranty
Challenge
family represents an innovative approach to
double-gantry rollover wash systems in
terms of structural design, technology and
performance.
The unit incorporates a patented system
providing extra fast wash and dry cycle
times exclusive to Petro Management Systems
Limited of this type. The result of close
and continuos collaboration between our
sales and design teams, CHALLENGE is the
flagship of Petro Management Systems
Limited gantry washing systems; rapid,
through washing and drying combined with
the quality for which Petro Management
Systems Limited has been renowed.
Available in two versions: Challenge and
Super-Challenge. Super-Challenge is
equipped with high pressure system. It
provides considerably improved washing and
drying performance. The dual pressure
operation of the horizontal and vertical
arches optimises the water pressure applied
to different surfaces of the vehicle to
give first class results. It can also
select different wash types (brushes,
chemical only, hybrid) offering a total of
16 different programmes.
Technical features:
New design - Brushes electronic power control -
Overlapping system with side brushes that are
automatically blocked in the forward gantry run
to improve washing of the lower parts and free
to tilt in the backward run to follow the
vehicle's profile - Inverter device controlling
the top brush and the top blower raising
movement - Drying system with 4 low noise air
blowers - Contour following top dryer - High
pressure system, up to 80 bar, with two side
arches and one contour following top arch - LED
traffic lights - Low power consumption - “Fault
tolerant” control system (faulty components are
automatically excluded if minor alarms occur
reducing therefore down times) - Hot dip
galvanized gantry
Overall dimensions:
Structure width: 3380 mm
Structure length: 1800 mm
Gantry height: 3125 mm
Washing width: 2400 mm
Washing height: 2400 mm
Maximum power consumption: 15,2 kW
(water pumps not included)
Main
accessories:
In-built wheel wash device / In-built Robowash
system / Underchassis wash / Short track device
/ High pressure / Side pre-wash arches /
Maximum flexibility to fit further chemical
products dosing pumps (shampoo and wax) /
Polish products and cycles / Wheel rims cleaner
and cycles / Possibility to use osmotic water /
Maximum flexibility to cope with special
vehicles shapes (ex. pick-up programme) / “Foam
touch” brushes / Centralized lubrication system
/ Different payment and activation systems.